Sample rate is how many times per second a sound is measured, and bitrate is how much data a file spends on each second of that sound. The two numbers sit side by side in a file's properties and answer different questions. Sample rate sets the highest pitch the file can hold. Bitrate sets how faithfully that sound survives compression.
Mixing them up leads to poor choices, such as converting a file to 48 kHz in the hope of better sound, or trusting a 320 kbps label on its own. This article keeps the two apart and then shows where they meet. For bitrate settings alone, the MP3 bitrate guide goes further.
Sample rate: how often the sound is measured
Digital audio stores sound as a series of snapshots of the waveform. The sample rate is the number of snapshots per second for each channel, written in hertz. At 44.1 kHz there are 44,100 every second. At 48 kHz there are 48,000.
One rule governs what that buys you. A sample rate can capture frequencies up to half its own value, so 44.1 kHz reaches 22.05 kHz and 48 kHz reaches 24 kHz. Human hearing tops out at about 20 kHz in young adults and lower with age. Both rates therefore cover everything audible. The CD standard is 44.1 kHz and the norm for video sound is 48 kHz. Neither sounds better than the other on playback.
Bitrate: how much data each second gets
Bitrate counts the bits used for each second of audio, in kilobits per second. For uncompressed audio it follows directly from three other numbers: sample rate times bit depth times channels. A CD works out at 44,100 samples times 16 bits times 2 channels, which is 1,411 kbps.
Compressed formats break that link. An MP3 encoder is told how many bits it may spend, up to 320 kbps, and decides what to keep within that allowance. At 128 kbps it has less than a tenth of the CD figure to work with. The method is described in how MP3 compression works.
Bit depth, the third number in that sum, is the precision of each sample. It applies to uncompressed and lossless audio, and an MP3 has no fixed bit depth. It is explained with the other digital audio basics.
Where the two numbers appear together
Five familiar kinds of audio show how the two figures pair up:
| Audio | Sample rate | Bitrate |
|---|---|---|
| Audio CD | 44.1 kHz | 1,411 kbps, uncompressed |
| Music MP3 | 44.1 kHz, sometimes 48 kHz | 128 to 320 kbps |
| YouTube AAC audio | Usually 44.1 kHz | About 128 kbps |
| YouTube Opus audio | 48 kHz | Up to about 160 kbps |
| Audiobook MP3 | Often 22.05 kHz | 32 to 64 kbps |
The table shows the two values moving independently. The same 44.1 kHz rate carries a CD and a 128 kbps MP3 alike. What changes between them is how much of the original detail is kept.
The YouTube rows explain a figure that puzzles people. An MP3 made from a video's Opus track will often be 48 kHz, not the 44.1 kHz familiar from CDs. There is no need to change it, since current phones and computers play both rates.
Bitrate vs sample rate inside an MP3
In theory a 44.1 kHz MP3 can carry sound up to 22 kHz. In practice the bitrate decides how much of that range is used. To save bits, encoders filter out the highest frequencies before they begin. A typical 128 kbps MP3 contains little or nothing above 16 to 17 kHz. At 320 kbps the cut-off sits near 20 kHz.
So a low bitrate narrows the audible range even though the sample rate stays the same. The reverse does not work. Raising the sample rate of a finished file adds empty headroom above the cut-off and no sound.
The two also interact at the bottom of the scale. At very low bitrates, encoders often halve the sample rate to 22.05 or 24 kHz. Fewer samples leave more bits for each one, and the lost top end matters little for speech.
Which one changes the file size
For an MP3, size depends on bitrate and length alone. To get megabytes, multiply the bitrate in kbps by the length in seconds, then divide by 8,000. A track of 3 minutes 30 seconds at 256 kbps is 256 times 210 divided by 8,000, or about 6.7 MB. It is the same size at 44.1 kHz and at 48 kHz.
Uncompressed audio behaves differently, because there the sample rate feeds straight into the bitrate. A stereo 16-bit WAV file takes about 10.6 MB per minute at 44.1 kHz and about 11.5 MB at 48 kHz. The two formats are set side by side in MP3 vs WAV.
What to do with the two numbers
To read the two numbers for a file you already have, open it in a free tool such as MediaInfo. It lists the bit rate in kb/s and the sampling rate in kHz on separate lines, next to the number of channels. The units tell them apart: kHz is always the sample rate and kbps is always the bitrate. Where Windows, a Mac and a phone show the same figures is covered in how to check the bitrate of an MP3.
Four rules of thumb follow from the difference between the two numbers:
- Leave the sample rate alone. Converting 44.1 kHz to 48 kHz, or the reverse, adds a processing step and no new sound.
- Choose the bitrate with the source in mind. Audio taken from a YouTube video was already compressed to roughly 128 to 160 kbps, so a 320 kbps MP3 of it is larger without being better.
- For speech, go lower on both. A mono recording has one channel to describe instead of two, so 64 kbps in mono gives a voice about the same budget as 128 kbps in stereo.
- Judge by listening on your own headphones, not by the largest figure on the label.
If the download options after a search on MP3Juice offer a choice of quality, the figure is the bitrate of the new file. The sample rate normally follows the source and needs no attention. For the whole chain from source to finished file, read what decides MP3 audio quality.
